Section 4123:1-5-06 - Portable explosive-actuated fastening tools(C) Design specifications.(1) High-velocity tools. Tools of the high-velocity type will have the following characteristics:
(a) The muzzle end of the tool will have a protective shield or guard at least three and one-half inches in diameter, mounted perpendicular to and concentric with the barrel, and designed to confine any flying fragments or particles that might otherwise create a hazard at the time of firing.(b) Where a standard shield or guard cannot be used, or where it does not cover all apparent avenues through which flying particles might escape, a special shield, guard, fixture, or jig, designed and built by the manufacturer of the tool being used, which provides this degree of protection, will be used as a substitute.(c) The tool will be so designed that it cannot be fired unless it is equipped with a standard protective guard or shield, or a special shield, guard, fixture or jig.(d) Firing the tool. (i) The firing mechanism will be so designed that the tool cannot fire during loading or preparation to fire, or if the tool should be dropped while loaded.(ii) The firing of the tool will be dependent upon at least two separate and distinct operations of the operator, with the final firing movement being separate from the operation of bringing the tool into the firing position.(e) The tool will be so designed as not to be operable other than against a work surface, and unless the operator is holding the tool against the work surface with a force at least five pounds greater than the total weight of the tool.(f) The tool will be so designed that it will not operate when equipped with the standard guard indexed to the center position if any bearing surface of the guard is tilted more than eight degrees from contact with the work surface.(g) The tool will be so designed that positive means of varying the power are available or can be made available to the operator as part of the tool, or as an auxiliary, in order to make it possible for the operator to select a power level adequate to perform the desired work without excessive force.(h) The tool will be so designed that all breeching parts will be reasonably visible to allow a check for any foreign matter that may be present.(2) Low-velocity - piston-type tools. Tools of the low-velocity piston type will have the following characteristics:
(a) The muzzle end of the tool will be designed so that suitable protective shields, guards, jigs, or fixtures, designed and built by the manufacturer of the tool being used, can be mounted perpendicular to the barrel. A standard spall shield will be supplied with each tool.(b) Firing the tool.(i) The tool will be designed so that it will not in ordinary usage propel or discharge a stud, pin, or fastener, while loading or during preparation to fire, or if the tool should be dropped while loaded.(ii) Firing of the tool will be dependent upon at least two separate and distinct operations of the operator, with the final firing movement being separate from the operation of bringing the tool into the firing position.(c) The tool will be so designed as not to be operable other than against a work surface, and unless the operator is holding the tool against the work surface with a force at least five pounds greater than the total weight of the tool.(d) The tool will be so designed that positive means of varying the power are available or can be made available to the operator as part of the tool, or as an auxiliary, in order to make it possible for the operator to select a power level adequate to perform the desired work without excessive force.(e) The tool will be so designed that all breeching parts will be reasonably visible to allow a check for any foreign matter that may be present.(D) Minimum instructions for qualifying operators. Instructions to operators in order to teach them the use of portable explosive-actuated fastening tools will include, but will not be limited to, the following items:
(1) Before using a tool, the operator will inspect it to determine to his satisfaction that it is clean, that all moving parts operate freely, and that the barrel is free from obstruction.(2) When a tool develops a defect during use, the operator will immediately cease to use it, until it is properly repaired.(3) Tools will not be loaded until just prior to the intended firing time. Neither loaded nor empty tools are to be pointed at any employee, and hands should be kept clear of the open barrel end.(4) No tools will be loaded unless being prepared for immediate use, nor will an unattended tool be left loaded.(5) In case of a misfire, the operator will hold the tool in the operating position for at least thirty seconds. He will then try to operate the tool a second time. He will wait another thirty seconds, holding the tool in the operating position; then he will proceed to remove the explosive load in strict accordance with the manufacturer's instructions. Misfired cartridges should be placed carefully in a metal container filled with water, and returned to the supervisor for disposal.(6) The tool will never be left unattended in a place where it would be available to unauthorized persons.(7) Fasteners will not be driven into very hard or brittle materials, including, but not limited to, cast iron, glazed tile, surface-hardened steel, glass block, living rock, face brick, or hollow tile.(8) Driving into materials easily penetrated will be avoided unless such materials are backed by a substance that will prevent the pin or fastener from passing completely through and creating a flying missile hazard on the other side.(9) Driving distance from edge(a) Fasteners will not be driven directly into materials such as brick or concrete closer than three inches from the unsupported edge or corner, or into steel surfaces closer than one-half inch from the unsupported edge or corner, unless a special guard, fixture, or jig, is used.(b) Exception: Low-velocity tools may drive no closer than two inches from an edge in concrete or one-fourth inch in steel.(c) When fastening other materials, such as a two- by four-inch wood section, to a concrete surface, it is permissible to drive a fastener of no greater than seven-thirty-seconds-inch shank diameter not closer than two inches from the unsupported edge or corner of the work surface.(10) Fasteners will not be driven through existing holes unless a positive guide is used to secure accurate alignment.(11) No fastener will be driven into a spalled area caused by an unsatisfactory fastening.(12) Tools will not be used in an explosive or flammable atmosphere.(13) All tools will be used with the correct shield, guard, or attachment recommended by the manufacturer.(14) Any tool found not in proper working order will be immediately removed from service. The tool will be inspected at regular intervals and will be repaired in accordance with the manufacturer's specifications.(E) Strength of charge - identification. All explosive charges (cartridges and shells) to be used in portable explosive-actuated tools will be marked by color, in accordance with table 6-1 to this rule, "Identification of Cased Loads," to designate the strength of the charge.
Table 6-1
Identification of Cased Loads
| Color Identification | |
Power Level | Case Color | Load Color | Nominal Velocity (= 45 f.p.s.) |
1 | Brass | Gray | 300 |
2 | Brass | Brown | 390 |
3 | Brass | Green | 480 |
4 | Brass | Yellow | 570 |
5 | Brass | Red | 660 |
6 | Brass | Purple | 750 |
7 | Nickel | Gray | 840 |
8 | Nickel | Brown | 930 |
9 | Nickel | Green | 1020 |
10 | Nickel | Yellow | 1110 |
11 | Nickel | Red | 1200 |
12 | Nickel | Purple | 1290 |
Note: The nominal velocity applies to 3/8-inch diameter "350-grain" ballistic slug fired in a test device and has no reference to actual fastener velocity developed in any specific size or type of tool.
Ohio Admin. Code 4123:1-5-06
Effective: 6/30/2023
Five Year Review (FYR) Dates: 2/1/2027
Promulgated Under: 119.03
Statutory Authority: 4121.12, 4121.121, 4121.13
Rule Amplifies: 4121.47
Prior Effective Dates: 04/01/1964, 08/01/1977, 01/01/1986, 04/10/2011, 02/01/2022