Ga. Comp. R. & Regs. 110-11-1-.20
Georgia State Amendments to the International Residential Code for One- and Two- Family Dwellings (2006 Edition) Georgia Department of Community Affairs Planning and Environmental Management Division 60 Executive Park South, N.E. Atlanta, Georgia 30329-2231 (404) 679-3118 Revised January 1, 2010 |
GEORGIA STATE MINIMUM STANDARD
ONE AND TWO FAMILY DWELLING CODE
(INTERNATIONAL RESIDENTIAL CODE FOR
ONE- AND TWO-FAMILY DWELLINGS
WITH GEORGIA STATE AMENDMENTS)
The INTERNATIONAL RESIDENTIAL CODE FOR ONE- AND TWO-FAMILY DWELLINGS, 2006 Edition, published by the International Code Council, when used in conjunction with these Georgia State Amendments and all other Georgia State Amendments to the INTERNATIONAL RESIDENTIAL CODE FOR ONE- AND TWO-FAMILY DWELLINGS, 2006 Edition, shall constitute the official Georgia State Minimum Standard One and Two Family Dwelling Code.
Part IV, Energy Conservation (Chapter 11), is deleted from the INTERNATIONAL RESIDENTIAL CODE FOR ONE- AND TWO-FAMILY DWELLINGS. Substitute all references to Chapter 11 ENERGY EFFICIENCY with references to the Georgia State Minimum Standard Energy Code (IECC with Georgia State Supplements and Amendments).
Part VII, Plumbing (Chapters 25 through 32), is deleted from the INTERNATIONAL RESIDENTIAL CODE FOR ONE- AND TWO-FAMILY DWELLINGS. Substitute for plumbing requirements the Georgia State Minimum Standard Plumbing Code (International Plumbing Code with Georgia State Amendments).
Part VIII, Electrical (Chapters 33 through 42), is deleted from the INTERNATIONAL RESIDENTIAL CODE FOR ONE- AND TWO-FAMILY DWELLINGS. Substitute for electrical requirements the Georgia State Minimum Standard Electrical Code (National Electrical Code with Georgia State Amendments).
GEORGIA STATE AMENDMENTS
CODE REFERENCE:
(a) Replace all references to the ICC Electrical Code with references to the Georgia State Minimum Standard Electrical Code (National Electrical Code with Georgia State Amendments).
(b) Replace all references to the International Energy Conservation Code (IECC) with references to the Georgia State Minimum Standard Energy Code (IECC with Georgia State Supplements and Amendments). The Georgia State Minimum Standard Energy Code shall be used for heating and air conditioning equipment.
SCOPE:
The provisions of the GeorgiaState Minimum Standard One and Two Family Dwelling Code shall apply to the construction, alteration, movement, enlargement, replacement, repair, equipment, use and occupancy, location, maintenance, removal and demolition of detached one- and two-family dwellings and multiple single-family dwellings (townhouses) not more than three stories in height with separate means of egress and their accessory structures.
APPENDICES:
Appendices are not enforceable unless they are specifically referenced in the body of the code or adopted by the Department of Community Affairs or the authority having jurisdiction.
GEORGIA STATE MINIMUM REQUIREMENTS FOR BOILERS/WATER HEATERS AND PRESSURE VESSELS
The State's minimum requirements for boilers/water heaters and pressure vessels over 200,000 BTU/h (58.61 kW), 210 degrees Fahrenheit or 120 gallons capacity shall be established by O.C.G.A. Title 34, Chapter 11 and the Rules and Regulations of the Georgia Department of Labor.
*Revise the International Residential Code for One- and Two-Family Dwellings, 2006 Edition, as follows:
CHAPTER 2
DEFINITIONS
SECTION R202
DEFINITIONS
*Add new definition 'Air-Impermeable Insulation' to Section R202 'Definitions' as follows:
AIR-IMPERMEABLE INSULATION. An insulation having an air permanence equal to or less than 0.02 L/s-m2 at 75 Pa pressure differential tested according to ASTM E 2178 or E 283.
(Effective January 1, 2010)
*Revise definition of 'Townhouse' of the 2009 Georgia Amendment to read as follows:
TOWNHOUSE. Multiple single-family dwelling units, separately owned, constructed in a group of three or more attached units in which each unit extends from foundation to roof and with a yard or public way onat least two sides.
(Effective January 1, 2010)
CHAPTER 8
ROOF-CEILING CONSTRUCTION
SECTION R806
ROOF VENTILATION
*Delete Section R806.4 'Conditioned attic assemblies' and substitute the following:
R806.4 Unvented attic assemblies. Unvented attic assemblies (spaces between the ceiling joists of the top story and the roof rafters) shall be permitted if all the following conditions are met:
1. The unvented attic space is completely contained within the building thermal envelope.
2. No interior vapor retarders are installed on the ceiling side (attic floor) of the unvented attic assembly.
3. Where wood shingles or shakes are used, a minimum 1/4 inch (6 mm) vented air space separates the shingles or shakes and the roofing underlayment above the structural sheathing.
4. Either Items a., b. or c. shall be met, depending on the air permeability of the insulation directly under the structural roof sheathing.
a. Air-impermeable insulation only. Insulation shall be applied in direct contact to the underside of the structural roof sheathing.
b. Air-permeable insulation only. In addition to the air-permeable insulation installed directly below the structural sheathing, rigid board or sheet insulation shall be installed directly above the structural roof sheathing as specified in Table R806.4 for condensation control.
c. Air-impermeable and air-permeable insulation. The air-impermeable insulation shall be applied in direct contact to the underside of the structural roof sheathing as specified in Table R806.4 for condensation control. The air-permeable insulation shall be installed directly under the air-impermeable insulation.
TABLE R806.4
INSULATION FOR CONDENSATION CONTROL
CLIMATE ZONE | MINIMUM RIGID BOARD OR AIR-IMPERMEABLE INSULATION R-VALUE a |
2B and 3B tile roof only | 0 (none required) |
1, 2A, 2B, 3A, 3B, 3C | R-5 |
4C | R-10 |
4A, 4B | R-15 |
5 | R-20 |
6 | R-25 |
7 | R-30 |
8 | R-35 |
a. Contributes to but does not supersede the requirements of the Georgia State Minimum Standard Energy Code.
(Effective January 1, 2010)
CHAPTER 15
EXHAUST SYSTEMS
SECTION M1502
CLOTHES DRYER EXHAUST
*Revise Section M1502.6 'Duct length' to read as follows:
M1502.6 Duct length. The maximum length of a clothes dryer exhaust duct shall not exceed 35 feet (10668 mm) from the dryer location to the wall or roof termination. The maximum length of the duct shall be reduced 2.5 feet (762 mm) for each 45-degree (0.79 rad) bend and 5 feet (1524 mm) for each 90-degree (1.57 rad) bend. The maximum length of the exhaust duct does not include the transition duct.
Exception: Where the make and model of the clothes dryer to be installed is known and the manufacturer's installation instructions for such dryer are provided to the code official, the maximum length of the exhaust duct, including any transition duct, shall be permitted to be in accordance with the dryer manufacturer's installation instructions. Where exhaust ducts are installed in concealed locations, the developed length of the exhaust duct system shall be indicated by permanent labels or tags installed in an observable location.
(Effective January 1, 2010)
CHAPTER 24
FUEL GAS
SECTION G2415 (404)
PIPING SYSTEM INSTALLATION
*Revise Section G2415.1 (404.1) 'Prohibited locations' to read as follows:
G2415.1 (404.1) Prohibited locations. Piping shall not be installed in or through a ducted supply, return or exhaust, clothes chute, chimney or gas vent, dumbwaiter or elevator shaft. Piping installed downstream of the point of delivery shall not extend through any townhouse unit other than the unit served by such piping.
(Effective January 1, 2010)
SECTION G2420 (409)
GAS SHUTOFF VALVES
*Revise Section G2420.5 (409.5) 'Equipment shutoff valve' to add exception number 2 as follows:
G2420.5 (409.5) Equipment shutoff valve.
Exceptions:
1. Shutoff valves for vented decorative appliances and decorative appliances for installation in vented fireplaces shall not be prohibited from being installed in an area remote from the appliance where such valves are provided with ready access. Such valves shall be permanently identified and shall serve no other equipment.
2. Shutoff valves for ranges/ovens and dryers shall be allowed to be located behind such equipment.
(Effective January 1, 2010)
SECTION G2439 (614)
CLOTHES DRYER EXHAUST
*Revise Section G2439.5.1 (614.6.1) 'Maximum length' to read as follows:
G2439.5.1 (614.6.1) Maximum length. The maximum length of a clothes dryer exhaust duct shall not exceed 35 feet (10668 mm) from the dryer location to the outlet terminal. The maximum length of the duct shall be reduced 2 1/2 feet (762 mm) for each 45 degree (0.79 rad) bend and 5 feet (1524 mm) for each 90 degree (1.57 rad) bend. The maximum length of the exhaust duct does not include the transition duct.
Exception: Where the make and model of the clothes dryer to be installed is known and the manufacturer's installation instructions for such dryer are provided to the code official, the maximum length of the exhaust duct, including any transition duct, shall be permitted to be in accordance with the dryer manufacturer's installation instructions. Where exhaust ducts are installed in concealed locations, the developed length of the exhaust duct system shall be indicated by permanent labels or tags installed in an observable location.
(Effective January 1, 2010)
End of Amendments.
Georgia State Amendments to the International Building Code (2006 Edition) Georgia Department of Community Affairs Planning and Environmental Management Division 60 Executive Park South, N.E. Atlanta, Georgia 30329-2231 (404) 679-3118 Revised January 1, 2010 |
GEORGIA STATE MINIMUM STANDARD BUILDING CODE (INTERNATIONAL BUILDING CODE WITH GEORGIA STATE AMENDMENTS)
The INTERNATIONAL BUILDING CODE, 2006 Edition, published by the International Code Council, when used in conjunction with these Georgia State Amendments and all other Georgia State Amendments to the INTERNATIONAL BUILDING CODE, 2006 Edition, shall constitute the official Georgia State Minimum Standard Building Code.
GEORGIA STATE AMENDMENTS
CODE REFERENCE:
(a) Replace all references to the ICC Electrical Code with references to the Georgia State Minimum Standard Electrical Code (National Electrical Code with Georgia State Amendments).
(b) Replace all references to the International Energy Conservation Code (IECC) with references to the Georgia State Minimum Standard Energy Code (IECC with Georgia State Supplements and Amendments). The Georgia State Minimum Standard Energy Code shall be used for efficiency and coefficient of performance ratings of equipment.
APPENDICES:
Appendices are not enforceable unless they are specifically referenced in the body of the code or adopted by the Department of Community Affairs or the authority having jurisdiction.
SCOPE:
The provisions of the Georgia State Minimum Standard Building Code shall apply to the construction, alteration, movement, enlargement, replacement, repair, equipment, use and occupancy, location, maintenance, removal and demolition of every building or structure or any appurtenances connected or attached to such buildings or structures.
Exception #1: Detached one- and two-family dwellings and multiple single-family dwellings (townhouses) not more than three stories high with separate means of egress and their accessory structures shall comply with the Georgia State Minimum Standard One and Two Family Dwelling Code (International Residential Code for One- and Two-Family Dwellings with Georgia State Amendments).
Exception #2: The following table titled 'Codes Reference Guide' establishes specific primary and supplementary code applications and is to be applied by the authority having jurisdiction.
CODES REFERENCE GUIDE | ||
Area | Primary | Supplement |
Occupancy Classification | LSC | IBC |
Building Construction Types Including allowable height, allowable building areas, and the requirements for sprinkler protection related to minimum building construction types. | IBC | LSC |
Means of Egress | LSC | NONE |
Standpipes | IBC | IFC |
Interior Finish | LSC | NONE |
HVAC Systems | IMC | NONE |
Vertical Openings | LSC | NONE |
Sprinkler Systems minimum construction standard | LSC | NONE |
Fire Alarm Systems | LSC | NONE |
Smoke Alarms and Smoke Detection Systems | State Statute and LSC | NONE |
Portable Fire Extinguishers | IFC | NONE |
Cooking Equipment | LSC and NFPA 96 | NONE |
Fuel Fired Appliances | IFGC | NFPA 54 |
Liquid Petroleum Gas | NFPA 58 | NFPA 54 or IFGC |
Compressed Natural Gas | NFPA 52 | NONE |
*Revise the International Building Code, 2006 Edition, as follows:
CHAPTER 7
FIRE-RESISTANCE-RATED CONSTRUCTION
SECTION 707
SHAFT ENCLOSURES
*Revise Section 707.14.1 'Elevator lobby', exception 9, of the Georgia Amendment revised January 1, 2007 to read as follows:
707.14.1 Elevator Lobby.
Exception:
9. Lobbies are not required where a listed elevator door opening protective device tested in accordance with UL1784 and compliant with ICC ES AC 77, is provided at the hoistway opening other than at the designated primary and alternate floors of elevator return. Written notification provided by installing party be provided to local fire responding party and the Georgia Department of Labor Safety Engineering.
(Effective January 1, 2010)
CHAPTER 16
STRUCTURAL DESIGN
SECTION 1603
CONSTRUCTION DOCUMENTS
*Revise and re-title Section 1603.1.8 'Systems and components requiring special inspections for seismic resistance' to read as follows:
1603.1.8 Special inspections statements on construction documents. The construction documents shall include as a minimum the requirements in Sections 1603.1.8.1 through 1603.1.8.3:
1603.1.8.1 Special inspections statement on construction documents. The content of the statement of special inspections required in Section 1705.2 shall be shown on the construction documents and shall include as a minimum the following:
1. The materials, systems, components and/or work required to have special inspections or testing by the building official or by the registered design professional responsible for each portion of the work.
2. The type and extent of each special inspection.
3. The type and extent of each test.
4. Additional requirements for special inspection or testing for seismic or wind resistance as specified in Section 1705.3, 1705.4, 1707 or 1708.
5. For each type of special inspection, identification as to whether it will be a continuous special inspection or a periodic special inspection.
1603.1.8.2 Final report statement for special inspections. The construction documents shall contain the following statement:
"Special inspection reports and a final report in accordance with Section 1704.1.2 of the Georgia State Minimum Standard Building Code shall be available at the time the building is approved for occupancy."
1603.1.8.3 Systems and components requiring special inspections for seismic resistance. Construction documents or specifications shall be prepared for those systems and components requiring special inspection for seismic resistance as specified in Section 1707.1 by the registered design professional responsible for their design and shall be submitted for approval in accordance with Section 107.1. Reference to seismic standards in lieu of detailed drawings is acceptable.
VERIFICATION AND INSPECTIONS | CONTINUOUS | PERIODIC | REFERENCED STANDARD | IBC REFERENCE |
12. Inspection of anchors installed in hardened concrete. | ---- | X | ACI 318: 3.8.6, 8.1.3, 21.2.8 | 1912.1 |
(Effective January 1, 2010)
CHAPTER 17
STRUCTURAL TESTS AND SPECIAL INSPECTIONS
SECTION 1704
SPECIAL INSPECTIONS
*Revise Table 1704.4 'Required Verification and Inspection of Concrete Construction' by adding line item 12 as follows:
(Effective January 1, 2010)
*Replace 2007 Georgia Amendment Table 1704.1 'Minimum Special Inspector Qualifications' See pages 7 through 9.
(Effective January 1, 2010)
CHAPTER 30
ELEVATORS AND CONVEYING SYSTEMS
SECTION 3002
HOISTWAY ENCLOSURES
*Revise Section 3002.4 'Elevator car to accommodate ambulance stretcher' to add exception as follows:
3002.4 Elevator car to accommodate ambulance stretcher.
Exception: Elevators with 50 feet or less of travel serving only one residence of a one- or two-family dwelling or townhouse shall be in compliance with ASME A17.1 as currently adopted and amended by the Georgia Department of Labor.
(Effective January 1, 2010)
CHAPTER 35
REFERENCED STANDARDS
*Revise the 'ACEC/G' reference of the 2007 Georgia Amendment to Chapter 35 'Referenced Standards' to read as follows:
ACEC/G | American Council of Engineering Companies of Georgia Harris Tower, Suite 700 233 Peachtree Street Atlanta, Georgia 30303 | |
Standard number reference | Title | Referenced in code section number |
ACEC/SEAOG SI GL 01-2009 | Georgia Special Inspections Guidelines.................1701.4, 2007GA Amendments (http://www.acecga.org/ to download document) | |
End of Amendments.
TABLE 1704.1 MINIMUM SPECIAL INSPECTOR QUALIFICATIONS | ||||
Category of Testing and Inspection | Minimum Qualifications (refer to key at end of Table) | |||
Shop Testing or Inspection | Field Testing or Inspection | Review Submittals | Review Testing, Certification, & Lab Reports | |
1704.2 Inspection of Fabricators | ||||
Pre-cast concrete | A, C, E | |||
Structural steel construction | C, F, G | |||
Wood construction | A | |||
Cold formed metal construction | A | |||
1704.3 & 1707.2 Steel Construction | ||||
Testing of welding | G | G | ||
Inspection of welding | C, F | C, F | ||
Material verification of structural steel, High strength bolts, nuts and washers | A | A, C | ||
Material verification of weld filler materials | C, F | |||
High strength bolting, inspection of steel frame joint details | A, C | |||
1704.4 & 1708.3 Concrete Construction | ||||
Reinforcing placement, cast-in-place bolts, post installed anchors, concrete and shotcrete placement and curing operations | A, C, H | |||
Pre-stressing steel installation | A, C, D, E | |||
Erection of pre-cast concrete members | A, C, H | |||
Concrete field sampling and testing | A, J | |||
Review certified mill reports and design mixes | A | |||
Verify use of required design mix | A, I, J, H, C | |||
Pre-stressed (pre-tensioned) concrete force application | A, C, E | |||
Post-tensioned concrete force application | A, C, D | |||
Review of in-situ concrete strength, prior to stressing of tendons in post-tensioned concrete and prior to removal of shores and forms from beams and structural slabs | A, C, D,H | |||
Reinforcing steel weldability, reinforcing welding, weld filler material | C, F | |||
Testing of welding of reinforcing steel | G | |||
1704.5 & 1708.1 Masonry | ||||
Review f'm prior to construction | A | |||
Mortar joint construction, grout protection and placement, materials proportion, type/size/location of reinforcement, structural elements, anchorage, and connectors | A, C, K | |||
Sampling/testing of grout/mortar specimens | A, C, L, M | |||
Observe preparation of masonry prisms for testing of compressive strength of masonry, f'm | A, C, K, L, M | |||
Inspection of welding of reinforcing steel | C, F | |||
Testing of welding of reinforcing steel | G | |||
1704.7 & 1803 Soils | ||||
Observe site preparation, fill placement testing of compaction for compliance with the construction documents for the project | A, C, I, N | |||
Observe test bearing materials below shallow foundations for ability to achieve design bearing capacity | A, C, N, I (Level III) | |||
Review compaction testing for compliance with the construction documents for the project | A | |||
1704.6 Wood Construction | ||||
Observe structural panel sheathing, size of framing members, nail or staple diameter and length, number of fastener lines, and spacing of fastener lines and fasteners for compliance with construction documents for the project | A | |||
1704.8, 1704.9 & 1808 Pile and Pier Foundations | ||||
Observe installation | A, N | |||
Observe load tests | A | |||
1704.10 Sprayed Fire-Resistant Materials | ||||
Observe surface conditions, application, average thickness and density of applied material, and cohesive/adhesive bond | A, C | |||
1704.11 Mastic and intumescent fire-resistant coatings | ||||
Observe application compliance with AWCI 12-B | A, C | |||
1704.12 Exterior Insulation and Finish Systems | ||||
Inspect EIFS systems | A, B, C, O | |||
1704.13 Special Cases | ||||
Work of unusual or special nature | A, B, O | |||
[F] 1704.14 Smoke Control | See Requirements of IBC Section [F] 1704.14.2. | |||
1705, 1707 & 1708 Seismic and Wind Resistance | ||||
Periodic inspection of fabrication, installation and/or anchorage of building systems and components | A | |||
KEY: Georgia Professional Engineer (GA PE) competent in the specific task area or graduate of accredited engineering/engineering technology program under the direct supervision of a GA PE. Georgia Registered Architect (GA RA) or graduate of accredited architecture/architecture technology program under the direction of a GA RA. International Code Council (ICC) Special Inspector Certification specific to the particular material and testing methodology applicable to each Category of Testing and Inspection listed in the table. Post-tensioning Institute (PTI) Certification, Level 2, bonded or unbonded as applicable. Pre-stressed Concrete Institute (PCI) Certified Inspector. American Welding Society (AWS) Certified Welding Inspector (CWI) or AWS Certified Associate Welding Inspector working under the direct on-site supervision of a CWI. American Society for Nondestructive Testing (ASNT) Level II certification, or a Level III certification if previously certified as a Level II in the particular material and testing methodology applicable to each Category of Testing and Inspection listed in the table. American Concrete Institute (ACI) Concrete Construction Special Inspector. National Institute for Certification in Engineering Technologies (NICET) Level II or higher certification specific to the particular material and testing methodology applicable to each Category of Testing and Inspection listed in the table. ACI Concrete Field Testing Technician with Grade 1 certification. Georgia Concrete and Products Association (GC&PA) - Masonry Association of Georgia (MAG) Masonry Construction Inspector Certification. National Concrete Masonry Association (NCMA) Concrete Masonry Testing Procedures certification. GC&PA - MAG Masonry Testing Technician certification. NICET Certified Engineering Technologist (CT). Other Qualified Special Inspector as approved by the Building Official. Notes: 1. The Special Inspector shall meet one of the minimum qualifications listed for the applicable Category of Testing and Inspection. 2. Materials testing shall be done by an Approved Testing Agency meeting the requirements of IBC Section 1703 and ASTM E 329. | ||||
Georgia State Amendments to the International Plumbing Code (2006 Edition) Georgia Department of Community Affairs Planning and Environmental Management Division 60 Executive Park South, N.E. Atlanta, Georgia 30329-2231 (404) 679-3118 Revised January 1, 2010 |
GEORGIA STATE MINIMUM STANDARD PLUMBING CODE (INTERNATIONAL PLUMBING CODE WITH GEORGIA STATE AMENDMENTS)
The International Plumbing Code, 2006 Edition, published by the International Code Council, when used in conjunction with these Georgia State Amendments and all other Georgia State Amendments to the International Plumbing Code, 2006 Edition, shall constitute the official Georgia State Minimum Standard Plumbing Code.
GEORGIA STATE AMENDMENTS
CODE REFERENCE:
(a) Replace all references to the ICC Electrical Code with references to the Georgia State Minimum Standard Electrical Code (National Electrical Code with Georgia State Amendments).
(b) Replace all references to the International Energy Conservation Code (IECC) with references to the Georgia State Minimum Standard Energy Code (IECCwith Georgia State Supplements and Amendments). The Georgia State Minimum Standard Energy Code shall be used for efficiency and coefficient of performance ratings of plumbing equipment.
GEORGIA STATE MINIMUM REQUIREMENTS FOR BOILERS/WATER HEATERS AND PRESSURE VESSELS
The State's minimum requirements for boilers/water heaters and pressure vessels over 200,000 BTU/h (58.61 kW), 210 degrees Fahrenheit or 120 gallons capacity shall be established by O.C.G.A. Title 34, Chapter 11 and the Rules and Regulations of the Georgia Department of Labor.
*Revise the International Plumbing Code, 2006 Edition, as follows:
APPENDIX C
GRAY WATER RECYCLING SYSTEMS
SECTION C102
SYSTEMS FOR FLUSHING WATER
CLOSETS AND URINALS
*Revise first sentence of Section C102.6 'Identification' of the 2009 Georgia Amendment to read as follows:
C102.6 Identification. Distribution plumbing fixtures and reservoirs shall be identified as containing nonpotable gray water. Piping shall be purple and identified in accordance with Section 608.8.
(Effective January 1, 2010)
*Add new Section C102.6.1 'Gray water valve identification' to the 2009 Georgia Amendment as follows:
C102.6.1 Gray water valve identification. Gray water valves shall be identified as nonpotable gray water and also identified as for the purpose of the valve.
(Effective January 1, 2010)
*Revise title of 'Appendix I' of the 2009 Georgia Amendment from 'Rain Water Recycling Systems' to 'Rain Water Harvesting Systems'. Also revise all other references in Appendix I from 'Rain Water Recycling Systems' to 'Rain Water Harvesting Systems'.
(Effective January 1, 2010)
SECTION I101
GENERAL
*Revise first sentence of Section I101.1 'Scope' of the 2009 Georgia Amendment to read as follows:
I101.1 Scope. The provisions of this appendix shall govern the materials, design, construction and installation of rain water systems for automatic clothes washers, flushing of water closets, flushing of urinals, and cooling tower makeup water. Nothing in this appendix shall be construed to restrict the use of rain water for outdoor irrigation.
(Effective January 1, 2010)
*Revise Section I101.9 'Potable water connections' of the 2009 Georgia Amendment to read as follows:
I101.9 Potable water connections. Only connections in accordance with Section I102.3 shall be made between a rain water harvesting system and a potable water system.
(Effective January 1, 2010)
*Delete Section I102.1 'Collection reservoir' of the 2009 Georgia Amendment in its entirety without substitution.
(Effective January 1, 2010)
End of Amendments.
Georgia State Amendments to the International Mechanical Code (2006 Edition) Georgia Department of Community Affairs Planning and Environmental Management Division 60 Executive Park South, N.E. Atlanta, Georgia 30329-2231 (404) 679-3118 Revised January 1, 2010 |
GEORGIA STATE MINIMUM STANDARD MECHANICAL CODE
(INTERNATIONAL MECHANICAL CODE WITH GEORGIA STATE AMENDMENTS)
The INTERNATIONAL MECHANICAL CODE, 2006 Edition, published by the International Code Council, when used in conjunction with these Georgia State Amendments and all other Georgia State Amendments to the INTERNATIONAL MECHANICAL CODE, 2006 Edition, shall constitute the official Georgia State Minimum Standard Mechanical Code.
GEORGIA STATE AMENDMENTS
CODE REFERENCE:
(a) Replace all references to the ICC Electrical Code with references to the Georgia State Minimum Standard Electrical Code (National Electrical Code with Georgia State Amendments).
(b) Replace all references to the International Energy Conservation Code (IECC) with references to the Georgia State Minimum Standard Energy Code (IECCwith Georgia State Supplements and Amendments). The Georgia State Minimum Standard Energy Code shall be used for efficiency and coefficient of performance ratings of mechanical equipment.
SCOPE:
The provisions of the Georgia State Minimum Standard Mechanical Code shall regulate the design, installation, maintenance, alteration and inspection of mechanical systems that are permanently installed and utilized to provide control of environmental conditions and related processes within buildings. This code shall also regulate those mechanical systems, system components, equipment and appliances specifically addressed herein. The installation of fuel gas distribution piping and equipment, fuel gas-fired appliances and fuel gas-fired appliance venting systems shall be regulated by the Georgia State Minimum Standard Gas Code (International Fuel Gas Code with Georgia State Amendments).
EXCEPTION: Detached one and two-family dwellings and multiple single-family dwellings (townhouses) not more than three stories high with separate means of egress and their accessory structures shall comply with the InternationalResidential Code.
APPENDICES:
Appendices are not enforceable unless they are specifically referenced in the body of the code or adopted by the Department of Community Affairs or the authority having jurisdiction.
GEORGIA STATE MINIMUM REQUIREMENTS FOR BOILERS/WATER HEATERS AND PRESSURE VESSELS
The State's minimum requirements for boilers/water heaters and pressure vessels over 200,000 BTU/h (58.61 kW), 210 degrees Fahrenheit or 120 gallons capacity shall be established by O.C.G.A. Title 34, Chapter 11 and the Rules and Regulations of the Georgia Department of Labor.
*Revise the International Mechanical Code, 2006 Edition, as follows:
CHAPTER 4
VENTILATION
SECTION 406
VENTILATION OF UNINHABITED SPACES
*Revise Section 406.1 'General' to add exception as follows:
406.1 General.
Exception: Unvented attic assemblies that comply with Section R806.4 of the International Residential Code.
(Effective January 1, 2010)
CHAPTER 5
EXHAUST SYSTEMS
SECTION 504
CLOTHES DRYER EXHAUST
*Revise Section 504.6.1 'Maximum length' to read as follows:
504.6.1 Maximum length. The maximum length of a clothes dryer exhaust duct shall not exceed 35 feet (10668 mm) from the dryer location to the outlet terminal. The maximum length of the duct shall be reduced 2 1/2 feet (762 mm) for each 45 degree (0.79 rad) bend and 5 feet (1524 mm) for each 90 degree (1.57 rad) bend. The maximum length of the exhaust duct does not include the transition duct.
Exception: Where the make and model of the clothes dryer to be installed is known and the manufacturer's installation instructions for such dryer are provided to the code official, the maximum length of the exhaust duct, including any transition duct, shall be permitted to be in accordance with the dryer manufacturer's installation instructions. Where exhaust ducts are installed in concealed locations, the developed length of the exhaust duct system shall be indicated by permanent labels or tags installed in an observable location.
(Effective January 1, 2010)
End of Amendments.
Georgia State Amendments to the International Fuel Gas Code (2006 Edition) Georgia Department of Community Affairs Planning and Environmental Management Division 60 Executive Park South, N.E. Atlanta, Georgia 30329-2231 (404) 679-3118 Revised January 1, 2010 |
GEORGIA STATE MINIMUM STANDARD
GAS CODE
(INTERNATIONAL FUEL GAS CODE
WITH GEORGIA STATE AMENDMENTS)
The INTERNATIONAL FUEL GAS CODE, 2006 Edition, published by the International Code Council, when used in conjunction with these Georgia State Amendments and all other Georgia State Amendments to the INTERNATIONAL FUEL GAS CODE, 2006 Edition, shall constitute the official Georgia State Minimum Standard Gas Code.
GEORGIA STATE AMENDMENTS
CODE REFERENCE:
Replace all references to the ICC Electrical Code with references to the Georgia State Minimum Standard Electrical Code (National Electrical Codewith Georgia State Amendments).
*Revise the International Fuel Gas Code, 2006 Edition, as follows:
CHAPTER 4
GAS PIPING INSTALLATIONS
SECTION 404 (IFGC)
PIPING SYSTEM INSTALLATION
*Revise Section 404.1 'Prohibited locations' to read as follows:
404.1 Prohibited locations. Piping shall not be installed in or through a ducted supply, return or exhaust, clothes chute, chimney or gas vent, dumbwaiter or elevator shaft. Piping installed downstream of the point of delivery shall not extend through any townhouse unit other than the unit served by such piping.
(Effective January 1, 2010)
SECTION 409 (IFGC)
SHUTOFF VALVES
*Revise Section 409.5 'Equipment shutoff valve' to add exception number 2 as follows:
409.5 Equipment shutoff valve.
Exceptions:
1. Shutoff valves for vented decorative appliances and decorative appliances for installation in vented fireplaces shall not be prohibited from being installed in an area remote from the appliance where such valves are provided with ready access. Such valves shall be permanently identified and shall serve no other equipment. Piping from the shutoff valve to within 3 feet (914 mm) of the appliance connection shall be sized in accordance with Section 402.
2. Shutoff valves for ranges/ovens and dryers shall be allowed to be located behind such equipment.
(Effective January 1, 2010)
CHAPTER 6
SPECIFIC APPLIANCES
SECTION 614 (IFGC)
CLOTHES DRYER EXHAUST
*Revise Section [M] 614.6.1 'Maximum length' to read as follows:
[M] 614.6.1 Maximum length. The maximum length of a clothes dryer exhaust duct shall not exceed 35 feet (10668 mm) from the dryer location to the outlet terminal. The maximum length of the duct shall be reduced 2 1/2 feet (762 mm) for each 45 degree (0.79 rad) bend and 5 feet (1524 mm) for each 90 degree (1.57 rad) bend. The maximum length of the exhaust duct does not include the transition duct.
Exception: Where the make and model of the clothes dryer to be installed is known and the manufacturer's installation instructions for such dryer are provided to the code official, the maximum length of the exhaust duct, including any transition duct, shall be permitted to be in accordance with the dryer manufacturer's installation instructions. Where exhaust ducts are installed in concealed locations, the developed length of the exhaust duct system shall be indicated by permanent labels or tags installed in an observable location.
(Effective January 1, 2010)
End of Amendments.
Georgia State Amendments to the International Fire Code (2006 Edition) Georgia Department of Community Affairs Planning and Environmental Management Division 60 Executive Park South, N.E. Atlanta, Georgia 30329-2231 (404) 679-3118 Revised January 1, 2010 |
GEORGIA STATE MINIMUM STANDARD FIRE CODE
(INTERNATIONAL FIRE CODE WITH GEORGIA STATE AMENDMENTS)
The INTERNATIONAL FIRE CODE, 2006 Edition, published by the International Code Council, when used in conjunction with these Georgia State Amendments and all other Georgia State Amendments to the International Fire Code 2006 Edition, shall constitute the official Georgia State Minimum Standard Fire Code.
GEORGIA STATE AMENDMENTS
CODE REFERENCE:
(a) Replace all references to the ICC Electrical Code with references to the Georgia State Minimum Standard Electrical Code (National Electrical Code with Georgia State Amendments).
(b) Replace all references to the International Energy Conservation Code (IECC) with references to the Georgia State Minimum Standard Energy Code (IECC with Georgia State Amendments). The Georgia State Minimum Standard Energy Code shall be used for efficiency and coefficient of performance ratings of equipment.
SCOPE:
The Georgia State Minimum Standard Fire Code establishes regulations affecting or relating to structures, processes and premises and safeguards from the hazards of fire and explosion arising from the storage, handling or use of structures, materials or devices; from conditions hazardous to life, property or public welfare in the occupancy of structures or premises; and from fire hazards in the structure or on the premise from occupancy or operation. It also applies to the construction, extension, repair, alteration or removal of fire suppression and alarm systems.
APPENDICES:
Appendices are not enforceable unless they are specifically referenced in the body of the code or adopted by the Department of Community Affairs or the authority having jurisdiction.
*Revise the International Fire Code, 2006 Edition, as follows:
CHAPTER 6
BUILDING SERVICES AND SYSTEMS
SECTION 603
FUEL-FIRED APPLIANCES
*Delete Section 603.4 of the 2007 Georgia Amendment in its entirety and insert in its place the following:
603.4 Portable unvented heaters. Portable unvented fuel-fired heating equipment shall be prohibited in occupancies in Groups A, E, I, R-1, R-2, R-3 and R-4.
Exceptions:
1. Listed and approved unvented fuel-fired heaters in one- and two-family dwellings and portable outdoor gas-fired heating appliances used outside one- and two-family dwellings.
2. Portable outdoor gas-fired heating appliances are allowed in accordance with Section 603.4.2.
603.4.1 Prohibited locations. Unvented fuel-fired heating equipment shall not be located in, or obtain combustion air from, any of the following rooms or spaces: sleeping rooms, bathrooms, toilet rooms or storage closets.
603.4.2 Portable outdoor gas-fired heating appliances. Portable gas-fired heating appliances located outdoors shall be in accordance with Sections 603.4.2.1 through 603.4.2.3.4.
603.4.2.1 Location. Portable outdoor gas-fired heating appliances shall be located in accordance with Sections 603.4.2.1.1 through 603.4.2.1.4.
603.4.2.1.1 Prohibited locations. The storage or use of portable outdoor gas-fired heating appliances is prohibited where any of the following exist:
1. Inside any occupancy when connected to the fuel gas container.
2. Inside tents, canopies and membrane structures.
3. On exterior balconies in accordance with NFPA 58.
603.4.2.1.2 Clearance to buildings. Portable outdoor gas-fired heating appliances shall be located at least 5 feet (1524 mm) from buildings.
603.4.2.1.3 Clearance to combustible materials. No portion of portable outdoor gas-fired heating appliances shall be located beneath, or closer than 5 feet (1524 mm) to combustible overhangs, awnings, sunshades or similar combustible attachments to buildings and combustible decorations.
603.4.2.1.4 Proximity to exits. Portable outdoor gas-fired heating appliances shall not be located within 10 feet (3048 mm) of exits or exit discharges.
603.4.2.2 Installation and operation. Portable outdoor gas-fired heating appliances shall be installed and operated in accordance with Sections 603.4.2.2.1 through 603.4.2.2.4.
603.4.2.2.1 Listing and approval. Only listed and approved heating appliances utilizing a fuel gas container that is integral to the appliance shall be used.
603.4.2.2.2 Installation and maintenance. Portable outdoor gas-fired heating appliances shall be installed and maintained in accordance with the manufacturer's instructions.
603.4.2.2.3 Tip-over switch. Portable gas-fired heating appliances shall be equipped with a tilt or tip-over switch that automatically shuts off the flow of gas if the appliance is tilted more than 15 degrees (0.26 rad) from vertical.
603.4.2.2.4 Guard against contact. The heating element or combustion chamber shall be permanently guarded so as to prevent accidental contact by persons or material.
603.4.2.3 Gas containers. Fuel gas containers for portable outdoor gas-fired heating appliances shall comply with Sections 603.4.2.3.1 through 603.4.2.3.4.
603.4.2.3.1 Approved containers. Only approved U.S. DOT or ASME gas containers shall be used.
603.4.2.3.2 Container replacement. Replacement of gas containers in the heating appliance shall not be conducted while the public is present.
603.4.2.3.3 Container capacity. The maximum individual capacity of gas containers used in connection with portable gas-fired heating appliances shall not exceed 20 pounds (9 kg).
603.4.2.3.4 Indoor storage prohibited. Gas containers shall not be stored inside of buildings except in accordance with Section 3809.9.
(Effective January 1, 2010)
End of Amendments.
Ga. Comp. R. & Regs. R. 110-11-1-.20