Section 62-701.210 - Documents Incorporated by ReferenceSpecific references to the documents listed below are made throughout this chapter. These documents are adopted as standards and are incorporated into this chapter by reference. The reference documents are available for inspection at the Department's district and Tallahassee offices, and may be obtained directly from the source.
(1) EPA document EPA/600/R-93/182, Quality Assurance and Quality Control for Waste Containment Facilities, September 1993.(2) 40 C.F.R. Parts 61.149, 61.150, 61.151, 61.154, Subpart M-National Emission Standard for Asbestos, July 1, 1992.(3) 40 C.F.R. Part 136, Appendix B, Definition and Procedure for the Determination of the Method Detection Limit, revision 1.1; October 26, 1984.(4) Method 9095, Paint Filter Test, found in EPA document EPA SW-846, Test Methods for Evaluating Solid Wastes, Physical/Chemical Methods; Third Edition, September, 1986, as revised, December, 1987.(5) Methods 601 and 602, 40 CFR Part 136, Appendix A, Methods for Organic Chemical Analysis of Municipal and Industrial Wastewater; December 22, 2000.(6)40 C.F.R. 258.13, Fault Areas: October, 1991.(7)40 C.F.R. 258.14, Seismic Impact Zones; October, 1991.(8)40 C.F.R. 258.15 Unstable Areas; October, 1991.(9) 40 C.F.R. 258, Appendices I and II; October, 1991.(11)40 C.F.R. 261.24 Table 1-Maximum Concentration of Contaminants for the Toxicity Characteristic; July, 1992.(12) GRI Test Method GM13 revision 9 dated June 1, 2009.(13) PGI 1104 Specification for PVC Geomembrane, effective April 15, 2008.(14) ASTM Method D5321/D5321M-14 "Standard Test Method for Determining Shear Strength of Soil-Geosynthetic and Geosynthetic-Geosynthetic Interfaces (ASTM D5321) by Direct Shear, " January 1, 2014, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, or at www.astm.org/Standard.(15) ASTM Method D4716/D4716M-14 "Test Method for Determining the (In-plane) Flow Rate per Unit Width and Hydraulic Transmissivity of a Geosynthetic Using a Constant Head, " (ASTM D4716) January 1, 2014, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, or at www.astm.org/Standard.(16) ASTM Method D5887-09 "Standard Test Method for Measurement of Index Flux Through Saturated Geosynthetic Clay Liner Specimens Using a Flexible Wall Permeameter, " (ASTM D5887) June 1, 2009, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, or at www.astm.org/Standard.(17) ASTM Method D6243/D6243M-13a "Standard Test Method for Determining the Internal and Interface Shear Resistance of Geosynthetic Clay Liner by the Direct Shear Method, " (ASTM D6243) July 1, 2013, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, or at www.astm.org/Standard.(18) GRI Test Method GM17 revision 6 dated June 1, 2009.(20) ASTM Method D6766-12 "Standard Test Method for Evaluation of Hydraulic Properties of Geosynthetic Clay Liners Permeated with Potentially Incompatible Aqueous Solutions, " (ASTM D6766) July 1, 2012, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, or at www.astm.org/Standard.(21) Secondary References. The ASTM Standards contained in subsections 62-701.210(14), (15), (16), (17) and (20), F.A.C., reference other standards that are listed collectively below. Any of these secondary reference documents may be obtained at 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, or at www.astm.org/Standard. (a) ASTM Method D653-14 "Standard Terminology Relating to Soil, Rock, and Contained Fluids, " August 1, 2014.(b) ASTM Method D698-12e1 "Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Standard Effort (12, 400 ft-lbf.ft3 (600 kN-m/m3)), " May 1, 2012.(c) ASTM Method D1557-12 "Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Modified Effort (56, 000 ft-lbf.ft3 (2, 700 kN-m/m3)), " May 1, 2012.(d) ASTM Method D2435/D2435M-11 "Standard Test Methods for One-Dimensional Consolidation Properties of Soils Using Incremental Loading, " May 1, 2011.(e) ASTM Method D2487-11 "Standard Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System), " May 1, 2011.(f) ASTM Method D3080/D3080M-11 "Standard Test Method for Direct Shear Test of Soils Under Consolidated Drained Conditions, " November 1, 2011.(g) ASTM Method D3740-12a "Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction, " May 1, 2012.(h) ASTM Method D4354-12 "Standard Practice for Sampling of Geosynthetics and Rolled Erosion Control Products (RECPs) for Testing, " July 1, 2012.(i) ASTM Method D4439-14 "Standard Terminology for Geosynthetics, " March 1, 2014.(j) ASTM Method D6243/D6243M-13a "Standard Test Method for Determining the Internal and Interface Shear Strength of Geosynthetic Clay Liner by the Direct Shear Method, " July 1, 2013.(k) ASTM Method D4491-99a(2014)e1 "Standard Test Methods for Water Permeability of Geotextiles by Permittivity, " January 1, 2014.(l) ASTM Method D5092-04(2010)e1 "Standard Practice for Design and Installation of Groundwater Monitoring Wells, " August 1, 2010.(m) ASTM Method D6574/D6574M-13e1 "Standard Test Method for Determining the (In-Plane) Hydraulic Transmissivity of a Geosynthetic by Radial Flow, " July 1, 2013.(n) ASTM Method E691-14 "Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method, " April 1, 2014.(o) ASTM Method D2216-10 "Standard Test Methods for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass, " July 1, 2010.(p) ASTM Method D4753-07 "Standard Guide for Evaluating, Selecting, and Specifying Balances and Standard Masses for Use in Soil, Rock, and Construction Materials Testing, " July 15, 2007.(q) ASTM Method E145-94(2011) "Standard Specification for Gravity-Convection and Forced-Ventilation Ovens, " December 1, 2011.(r) ASTM Method D5321/D5321M-14 "Standard Test Method for Determining the Shear Strength of Soil-Geosynthetic and Geosynthetic-Geosynthetic Interfaces by Direct Shear, " January 1, 2014.(s) ASTM Method D6072/D6072M-09 "Standard Practice for Obtaining Samples of Geosynthetic Clay Liners, " January 1, 2015.(t) ASTM Method D5887-09 "Standard Test Method for Measurement of Index Flux Through Saturated Geosynthetic Clay Liner Specimens Using a Flexible Wall Permeameter, " June 1, 2009.Fla. Admin. Code Ann. R. 62-701.210
Rulemaking Authority 403.061, 403.704 FS. Law Implemented 403.061, 403.702-.717 FS.
New 1-6-93, Amended 1-2-94, Formerly 17-701.210, Amended 5-27-01, 1-6-10, 8-12-12, Amended by Florida Register Volume 41, Number 022, February 3, effective 2/15/2015, Amended by Florida Register Volume 42, Number 041, March 1, 2016 effective 3/13/2016.New 1-6-93, Amended 1-2-94, Formerly 17-701.210, Amended 5-27-01, 1-6-10, 8-12-12, 2-15-15, 3-13-16.